Protocol Converter
AW-IF400G
Before attempting to connect, operate or adjust this product,
please read these instructions completely.
WARNING:
CAUTION:
• TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD AND ANNOYING INTERFERENCE, USE
THE RECOMMENDED ACCESSORIES ONLY.
• THE APPARATUS SHALL NOT BE EXPOSED TO
DRIPPING OR SPLASHING AND THAT NO
OBJECTS FILLED WITH LIQUIDS, SUCH AS
VASES, SHALL BE PLACED ON THE
APPARATUS.
Note:
The rating plate (serial number plate) is on the
bottom of the unit.
indicates safety information.
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)
This symbol on the products and/or accompanying documents means that used electrical and electronic
products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection points, where
they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your
products to your local retailer upon the purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent any potential negative
effects on human health and the environment which could otherwise arise from inappropriate waste handling.
Please contact your local authority for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
- 2 (E) -
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the
applicable safety instructions listed below. Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
10) Protect the power cord form being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
12) Use only with the cart, stand, tripod,
bracket, or table specified by
the manufacturer, or sold with the
apparatus. When a cart is used, use
c a u t i o n w h e n m ov i n g t h e
cart/apparatus combination to avoid
injury from tip-over.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding-
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
- 3 (E) -
indicates safety information.
Contents
Precautions for use .......................................................... 4
Introduction ....................................................................... 5
Major operating controls and their functions ................ 6
Connections ...................................................................... 9
When using the extended distance transmission
function of AW-RP400 and AW-PH400 ...................... 16
When using the extended distance transmission
function of AW-RP400 and AW-PH360 ...................... 17
Appearance ..................................................................... 18
Specifications ................................................................. 19
When controlling AW-PH400 from
AW-RP605A (AW-RP605) .......................................... 10
When controlling AW-PH400 from AW-RP555 ............ 11
When controlling AW-PH400 from AW-RP655 ............ 12
When controlling AW-PH350 from AW-RP400 ............ 13
When controlling AW-PH360 from AW-RP400 ............ 14
When controlling AW-PH650 from AW-RP400 ............ 15
Precautions for use
• Power Off Before Connecting or Disconnecting Cables.
Before plugging or unplugging the cables, be sure to switch
power off.
• Avoid Humidity and Dust.
Avoid using the product at a humid, dusty place because
much humidity and dust will cause damage to the parts
inside.
• Handle Carefully.
Do not drop the product, or subject it to strong shock or
• Operating Temperature Range
vibration. This is important to prevent trouble.
Avoid using the product at a cold place below 14°F (–10°C)
or at a hot place above 113°F (+45°C) because extremely
low or high temperature will adversely affect the parts
inside.
- 4 (E) -
Introduction
By using this unit, AW-PH400 can be controlled from AW-RP605/AW-RP605A/AW-RP655/AW-RP555.
Additionally, the controllable distance between AW-RP400 and AW-PH400/AW-PH360 can be extended up to
3,280 feet (1,000 meters).
AW-PH350/AW-PH360/AW-PH650 can also be controlled from AW-RP400.
Notes
The connections other than above examples cannot be done.
When controlling the AW-PH400 from the AW-RP605A:
• The AW-PH400 has no backlash so it is not necessary to adjust the backlash compensation.
• The maximum memory time of the tracing memory is 300 seconds.
• DIAGONAL MOTION cannot be set from ON to OFF or vice versa. It is always in effect.
• PRESET SPEED can be changed by setting DIAGONAL MOTION to ON and adjusting the DIAGONAL SPEED value.
• The maximum controllable distance is 1,000 meters between the AW-RP605A and AW-IF400G and 500 meters between the
AW-PH400 and AW-IF400G.
When controlling the AW-PH350 from the AW-RP400:
• The tracing memory data cannot be stored, played or deleted.
• TILT RANGE cannot be switched. It is fixed at 190 degrees.
• Backlash in the AW-PH350 cannot be compensated for.
• DIAGONAL MOTION cannot be set.
• The maximum controllable distance is 500 meters between the AW-RP400 and AW-IF400G and 1,000 meters between the
AW-PH350 and AW-IF400G.
- 5 (E) -
Major operating controls and their functions
Front panel
Power LED [POWER]
Extended Distance Transmission LED [EXTENSION]
This lights up green when DC power is supplied to the DC
12 V input connector .
This lights up when this unit is used to extend the
transmission distance between AW-RP400 and
AW-PH400.
Transmission Status LED [COMMUNICATE]
This lights up when data is being transmitted between the
controller and pan/tilt head.
- 6 (E) -
Major operating controls and their functions
Rear panel
Controller connector [CONTROLLER]
Use the controller CONTROL OUT TO PAN/TILT terminal
and a 10BASE-T (equivalent to UTP category 5) straight
cable for connection.
Pan/tilt head connector [PAN-TILT HEAD]
Use the pan/tilt head IP/RP terminal and a 10BASE-T
(equivalent to UTP category 5) straight cable for
connection.
- 7 (E) -
Major operating controls and their functions
Function Switches [SW1, SW2, SET UP]
(Factory defaults: SW1 = OFF, SW2 = OFF,
DC 12 V input connector [DC12V IN]
Connect the AW-PS505A AC adapter (sold separately) to
this socket.
SET UP No.1 = ON, SET UP No.2 to 4 = OFF)
This is used to select the operations of the AW-IF400.
Before changing a setting, the power must be turned off.
SETUP No.3 is the tilt range selector switch which is used
to control the AW-PH400 from the AW-RP605A.
At the ON position, the range is 300 degrees; at the OFF
position, it is 190 degrees. For any other combination, use
the switch at the OFF position.
Cable clamp
This is used to clamp the power cable in place and
prevent it from coming loose.
SET UP
SW1 SW2
Functions
No.1 No.2
MODE SET
No.3
No.4
TILT RANGE
NOT USE
ON
OFF
Controlling PH400 from RP605A
OFF OFF ON OFF
OFF
(300 deg) (190 deg)
Extending communication distance
between RP400 and PH400
OFF
(Set at RP400)
ON ON OFF OFF
OFF ON OFF ON
OFF
OFF
Controlling PH350 from RP400
OFF
- 8 (E) -
Connections
• Before proceeding with the connections, turn off the power.
• For further details on connecting the devices, refer to the operating instructions accompanying
the devices concerned.
• For further details on operating the devices, refer to the operating instructions accompanying
the devices concerned.
• Use a separate cable compensator if the video signal cable is longer than 500 meters.
- 9 (E) -
Connections
When controlling AW-PH400 from AW-RP605A (AW-RP605)
Zoom lens
Main unit
10BASE-T (UTP category 5)
straight cable
(max. 1000 m)
Camera cable
supplied with
AW-PH400
CONTROL OUT
TO PAN/TILT HEAD
AC adapter
AW-PS505A
(max. 500 m)
Convertible
camera
IP/RP
AC power cable
supplied with
AW-PH400
Control panel
Indoor pan/tilt head
Protocol converter
AW-IF400G
AW-PH400
• Switch settings
Multi-function controller
AW-RP605A
SET UP
3
SW1 SW2
AC adapter
AW-PS505A
1
2
4
ON
OFF
OFF OFF ON OFF
OFF
(300 deg) (190 deg)
- 10 (E) -
Connections
When controlling AW-PH400 from AW-RP555
Zoom lens
Camera cable
supplied with
AW-PH400
10BASE-T (UTP category 5)
straight cable
(max. 1000 m)
(max. 500 m)
Convertible
camera
IP/RP
AC power cable
supplied with
AW-PH400
Indoor pan/tilt head
Protocol converter
AW-IF400G
Multi hybrid control panel
AW-RP555
AW-PH400
• Switch settings
SET UP
3
SW1 SW2
AC adapter
AW-PS505A
AC adapter
AW-PS505A
1
2
4
ON
OFF
OFF OFF ON OFF
OFF
(300 deg) (190 deg)
- 11 (E) -
Connections
When controlling AW-PH400 from AW-RP655
Zoom lens
Camera cable
supplied with
AW-PH400
10BASE-T (UTP category 5)
straight cable
(max. 1000 m)
(max. 500 m)
Convertible
camera
IP/RP
AC power cable
supplied with
AW-PH400
Multi-function controller
AW-RP655
Indoor pan/tilt head
Protocol converter
AW-IF400G
AW-PH400
• Switch settings
SET UP
3
SW1 SW2
AC adapter
AW-PS505A
AC adapter
AW-PS505A
1
2
4
ON
OFF
OFF OFF ON OFF
OFF
(300 deg) (190 deg)
- 12 (E) -
Connections
When controlling AW-PH350 from AW-RP400
Zoom lens
Camera cable
AW-CA50T29
AW-CA50C29
10BASE-T (UTP category 5)
straight cable
CONTROL OUT
TO PAN/TILT
HEAD
Convertible
camera
(max. 500 m)
AC adapter
AW-PS505A
CONTROL IN
IP/RP
(max. 1000 m)
Indoor pan/tilt head
AC adapter
AW-PS300A
AW-PH350
Protocol converter
AW-IF400G
Pan/tilt control panel
AW-RP400
Remote
operation
panel
• Switch settings
AW-CB400
SET UP
AC adapter
AW-PS505A
SW1 SW2
1
2
3
4
OFF ON OFF ON OFF OFF
- 13 (E) -
Connections
When controlling AW-PH360 from AW-RP400
(The tracing memory function is not available.)
Set the SW1 switch on the CPU circuit board of AW-PH360 to “For RP605”.
Zoom lens
Camera cable
supplied with
AW-PH360
(For details, refer to the operating instructions for the AW-PH360.)
10BASE-T (UTP category 5)
CONTROL OUT
straight cable
TO PAN/TILT
Convertible
camera
HEAD
AC adapter
AW-PS505A
(max. 500 m)
CONTROL IN
IP/RP
(max. 1000 m)
Indoor pan/tilt head
AC adapter
AW-PS300A
AW-PH360
Protocol converter
AW-IF400G
Pan/tilt control panel
AW-RP400
Remote
operation
panel
• Switch settings
SET UP
SW1 SW2
AW-CB400
1
2
3
4
AC adapter
AW-PS505A
OFF ON OFF ON OFF OFF
- 14 (E) -
Connections
When controlling AW-PH650 from AW-RP400
(For the connections of the AW-PH650 pan/tilt head, camera housing, and
camera, refer to the operating instructions for the AW-PH650.)
10BASE-T (UTP category 5)
CONTROL OUT
straight cable
TO PAN/TILT
HEAD
(max. 500 m)
AC adapter
AW-PS505A
Outdoor
pan/tilt head
AW-PH650
REMOTE
POWER
RJ-45 relay adapter
(max. 1000 m)
To be locally
purchased
Protocol converter
AW-IF400G
Pan/tilt control panel
AW-RP400
Remote
operation
panel
• Switch settings
SET UP
AW-CB400
AC adapter
AW-PS505A
SW1 SW2
1
2
3
4
OFF ON OFF ON OFF OFF
- 15 (E) -
Connections
When using the extended distance transmission function
of AW-RP400 and AW-PH400
Zoom lens
10BASE-T (UTP category 5)
CONTROL OUT
straight cable
TO PAN/TILT
HEAD
(max. 500 m)
AC adapter
AW-PS505A
Camera cable
supplied with
AW-PH400
(max. 500 m)
Convertible
camera
IP/RP
AC power cable
supplied with
AW-PH400
Indoor pan/tilt head
AW-PH400
Protocol converter
AW-IF400G
Pan/tilt control panel
AW-RP400
Remote
operation
panel
• Switch settings
AW-CB400
SET UP
AC adapter
AW-PS505A
SW1 SW2
1
2
3
4
ON
ON OFF OFF OFF OFF
- 16 (E) -
Connections
When using the extended distance transmission function
of AW-RP400 and AW-PH360
Zoom lens
Camera cable
supplied with
AW-PH360
(The tracing memory function is available.)
10BASE-T (UTP category 5)
CONTROL OUT
straight cable
TO PAN/TILT
Convertible
camera
HEAD
AC adapter
AW-PS505A
(max. 500 m)
(max. 500 m)
Indoor pan/tilt head
AC adapter
AW-PS300A
AW-PH360
Protocol converter
AW-IF400G
Pan/tilt control panel
AW-RP400
Remote
operation
panel
• Switch settings
AW-CB400
SET UP
AC adapter
AW-PS505A
SW1 SW2
1
2
3
4
ON
ON OFF OFF OFF OFF
- 17 (E) -
Appearance
For mounting and other applications, use the screw
(M3 screw) holes in the side panels.
Do not use screws longer than 10 mm.
Unit: inch (mm)
M3 screw hole
(in 4 locations)
(Located in the
same positions
on both sides)
5-11/16
(145)
1/4
(6)
- 18 (E) -
Specifications
Source voltage:
DC 10.8 V to DC 16.0 V
Power consumption: 1.5 W
indicates safety information.
Controller supported:
AW-RP400, AW-RP555, AW-RP605, AW-RP605A, AW-RP655
AW-PH350, AW-PH360, AW-PH400, AW-PH650
Pan/tilt head supported:
Input connectors
DC 12 V IN socket:
Supply DC 12 V from the general-purpose AC adapter.
(Recommended AC adapter: AW-PS505A)
Input/Output connector
CONTROLLER:
RJ45, modular jack
10BASE-T straight cable (UTP category 5)
PAN-TILT HEAD:
RJ45, modular jack
10BASE-T straight cable (UTP category 5)
Switch functions:
Indicator:
Controller / Pan/Tilt Head selector switch (SW1, SW2, SET UP)
POWER, COMMUNICATE, EXTENSION
Allowable operating temperature:
14°F to 113°F (–10°C to +45°C)
Ambient operating humidity: 30% to 90% (no condensation)
Dimensions (WHD):
Weight:
5-11/16”1-3/16”3-3/8” (1453085 mm) (excluding rubber feet)
Approx. 0.9 lbs. (0.4 kg)
Finish:
AV ivory paint (color resembling Munsell 7.9Y 6.8/0.8)
Weight and dimensions indicated are approximate.
Specifications are subject to change without notice.
- 19 (E) -
- 20 (E) -
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY
UNIT COMPANY OF PANASONIC CORPORATION OF NORTH AMERICA
Executive Office:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000
EASTERN ZONE:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621
Southeast Region:
1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835
Central Region:
1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200
WESTERN ZONE:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
Government Marketing Department:
52 West Gude Drive, Rockville, MD 20850 (301) 738-3840
Broadcast PARTS INFORMATION & ORDERING:
9:00 a.m. – 5:00 p.m. (PST) (800) 334-4881/24 Hr. Fax (800) 334-4880
Emergency after hour parts orders (800) 334-4881
TECHNICAL SUPPORT:
Emergency 24 Hour Service (800) 222-0741
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010
Panasonic de Mexico S.A. de C.V.
Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127
Panasonic Puerto Rico Inc.
San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630 (787) 750-4300
© 2006 Matsushita Electric Industrial Co., Ltd. All rights reserved.
Matsushita Electric Industrial Co., Ltd.
Web Site: http://panasonic.net
松下电器产业株式会社
Web Site: http://panasonic.net
Printed in Japan
Gedruckt in Japan
Imprimé au Japon
Stampato in Giappone
Impreso en Japón
Напечатано в Японии
在日本印制
松下電器産業株式会社 ブロードメディア本部
〒223-8639 横浜市港北区綱島東4丁目3番1号
フリーダイヤル 0120
-
878
-
410
© 2006 Matsushita Electric Industrial Co., Ltd.
(松下電器産業株式会社)
All Rights Reserved.
D
VQTB0107-1
F0206S1066
|
Minolta Digital Camera XK User Manual
Muratec Marine Radio IC F50 User Manual
Nextar DVD Player MP301 User Manual
Nokia Network Card AD 5B User Manual
Nokia Satellite TV System 9600C User Manual
Nortel Networks IP Phone NN43117 110 0101 User Manual
Nortel Networks Telephone MICS XC User Manual
Omega Automobile Parts HHT21A User Manual
Panasonic DVR DMR EX85 User Manual
ParaBody Home Gym PBF460 User Manual